Skip to main content

Redmi POCO F1 Features

By


Defying the modern convention of building phones with metal and glass the new POCO has gone for more robust and user friendly plastic build. The F1 starts at 20,999 for the base 6GB/64GB variant and goes upto 29,999 for 8GB/256GB variant with a Kevlar type rear panel. POCO claims that it can resist scratches. However, the overall fit and finish isnt as impressive comparing other redmi phones.

 It has a 3.5mm headphone jack, USB C port and an expandable memory slot.

F1 has a 6.1 inch full HD display+IPS LCD display with a notch on top similar to VIVO V9. The F1 is build in Snapdragon 845 chip and Liquid cooling system. The company assures phone's speed and effortless multi tasking. The liquid cooling feature keeps temperature in control. For capturing good looking images the device have 12MP+5MP rear camera and a 20MP front camera with Pixel binning. Battery capacity is 4000mah which will keep device running for more than a day even in moderate usage. 

 300% increase in speed as compared with 835 processor. Octa core Kryo 385 CPU structure. Adreno 630 makes 30% improved GPU performance over Adreno 540. 

 Same price range phones are VIVO V9 Youth to VIVO V9 64GB which has maximum 660 processor. Battery capacity is also below POCO F1. 

 IR face lock and finger print also enabled. 4G dual sim either 2 nano sim or a nano sim+ SD. 

Comments

Post a Comment

Popular posts from this blog

Machining Processes & Machine Tool operations MCQ Mechanical

By
1. The cutting edge of the tool is perpendicular to the direction of tool travel in                                   A. Orthogonal cutting of metals  B. Oblique cutting of metals C. Both a and b D. None of these Ans: Orthogonal cutting of metals 2. The cutting edge of the tool is inclined at an angle less than 90 to the direction of tool travel in A. Orthogonal cutting of metals B. Oblique cutting of metals C. Both a and b D. None of these Ans: Oblique cutting of metals 3. Two components of the cutting forces which are perpendicular acting on the cutting tool in A. Orthogonal cutting of metals B. Oblique cutting of metals C. Both a and b D. None of these Ans: Orthogonal cutting of metals 4. Orthogonal cutting systems are also known as A. One dimesional cutting system B. Two dimensional cutting system C. Three dimensional cutting system D. none of ...
3 comments
Read more

What is moment of inertia?

By
Hi all, welcome to my blog. Today lets discuss about the topic moment of inertia. Every one of you may have heard about moment of inertia but only through mathematical terms.  Lets check the name again, "Moment of inertia" Split it in to two "Moment" of "inertia" Lets see, what is inertia Check the image above Lets consider they are in a race, in most conditions the probability of the thin guy winning is more. Why is the fat boy is slow? Because of his mass right? His mass is opposing his speed, thin guy has also a mass but th opposition is very low. In the same way inertia is an opposing virtual force. Now lets check the word moment, check the fishing rod, a force is applied at both the ends, and the rod bends. This is called moment, the turning force. Both force are in downward direction and the rod bends. I think the idea is clear, Moment of inertia means resistance to the turning force. Moment of inertia may change according to selection of forces, if ...
Post a Comment
Read more

Safety Operating Procedures required in an LPG plant

By
https://anurageros.blogspot.in/2017/09/safety-operating-procedures-required-in.html STANDARD OPERATING PROCEDURES : LEAK DETECTOR (VL/BL DETECTION) 1.        DRAIN OUT THE WATER FROM THE AIRLINE . BLOW OUT DIRT AND WATER FROM THE FILTER REGULATOR UNIT OF LD-01. CLEAN ALL THE PHOTO DIFFUSIVE SENSORS OF LD-01 2.        RESET LD-01 BY PRESSING THE (.) DOT BUTTON ON THE TOP RIGHT CORNER OF HMI AND WAIT TILL ‘CUC IN PROCESS MODE’ DISPLAYS. PRESS START BUTTON 3.        PUT VL TEST CYLINDER ON THE CONVEYOR. 4.        CHECK WHETHER THE UNIT IS REJECTING IT OR NOT. IF THE CYLINDER IS NOT GETTING REJECTED ADJUST THE SENSITIVITY SO THAT VL CYLINDERS OF LEAKAGE ABOVE 0.5GM/HR ARE REJECTED. 5.        CARRY OUT THE CHECK EVERY TWO HOURS AND RECORD IT. STANDARD OPERATING PROCEDURES : LEAK DETECTOR (O RING LEAK DETECTION) 1. ...
1 comment
Read more