RRB exam First stage CBT Results 2018

RRBs had notified 26,502 vacancies for the posts of Assistant Loco Pilot (ALP) and Technicians. In terms of Para 7 under the heading “Important Instructions” of CEN 01/2018 these vacancies were provisional. Further, attention is also drawn to the Notice dated 01.08.2018 published on the official websites of RRBs stating that the vacancies are likely to be increased to about 60,000.

Accordingly, the Vacancies have now been enhanced and the revised vacancies are as under:
Sl No Post Category Vacancy
1 Assistant Loco Pilot 27795
2 Various posts of Technicians 36576
Total 64371

The RRB & Railway wise summary of vacancies is given in the Revised Vacancy Table. It is to be noted that Railways reserve the right to either increase or decrease the vacancies mentioned above as per the actual requirement of Railways at the time of empanelment of candidates.

RRB FIRST STAGE CBT RESULT

((( RESULT )))

Comments

What is moment of inertia?

Hi all, welcome to my blog. Today lets discuss about the topic moment of inertia. Every one of you may have heard about moment of inertia but only through mathematical terms. Lets check the name again, "Moment of inertia" Split it in to two "Moment" of "inertia" Lets see, what is inertia Check the image above Lets consider they are in a race, in most conditions the probability of the thin guy winning is more. Why is the fat boy is slow? Because of his mass right? His mass is opposing his speed, thin guy has also a mass but th opposition is very low. In the same way inertia is an opposing virtual force. Now lets check the word moment, check the fishing rod, a force is applied at both the ends, and the rod bends. This is called moment, the turning force. Both force are in downward direction and the rod bends. I think the idea is clear, Moment of inertia means resistance to the turning force. Moment of inertia may change according to selection of forces, if ...

Machining Processes & Machine Tool operations MCQ Mechanical

1. The cutting edge of the tool is perpendicular to the direction of tool travel in A. Orthogonal cutting of metals B. Oblique cutting of metals C. Both a and b D. None of these Ans: Orthogonal cutting of metals 2. The cutting edge of the tool is inclined at an angle less than 90 to the direction of tool travel in A. Orthogonal cutting of metals B. Oblique cutting of metals C. Both a and b D. None of these Ans: Oblique cutting of metals 3. Two components of the cutting forces which are perpendicular acting on the cutting tool in A. Orthogonal cutting of metals B. Oblique cutting of metals C. Both a and b D. None of these Ans: Orthogonal cutting of metals 4. Orthogonal cutting systems are also known as A. One dimesional cutting system B. Two dimensional cutting system C. Three dimensional cutting system D. none of ...

Mutual Funds Or Stocks??

Is investing money in mutual funds good or should I go for stocks? A lot of investors have become wise enough to understand that it makes sense to invest when the market is down. Most of the investors are willing to take advantage of the current economic downfall. But the biggest question is: Should we invest in mutual funds or stocks? I had a similar doubt before I did my research last year. Please read this answer till the end and you will get your answer: What if I tell you that there are high chances that around half of the companies in Nifty 50 would vanish in the next 10 years? Some of them would even go bankrupt. Shocked? Not possible? What if I tell you that this is what has happened in the last 10 years. 22 out of 50 companies in Nifty 50 in 2009 do not even exist in Nifty 50 in 2019. Yes, you heard it right. 22 companies!! What are these companies? In 2009, did you imagine that Reliance Communication would go bankrupt? Did you imagine that Suzlon would be such a b...

Anurageros.blogspot.in

Search This Blog