Skip to main content

POST DIPLOMA COURSES UNDER MSME

By
Central institute of tool design Under Govt of India in Hyderabad invites both Diploma and  Btech candidates for their Post diploma courses. For students who have completed Diploma or Btech this would be a better job oriented course for skill development. All of you should pursue this opportunity. Detailed advertisement, Application form and Prospectus available in the link given below.

Filled Application form along with Application fee should be sent to The Director(trg), CITD,Balanagar, Hyderabad-500 037

Important dates

Application forms Available from                             08.07.2019
Last date of receipt of filled Application form          14.08.2019
Last date of Admission                                              18.08.2019

Comments

Post a Comment

Popular posts from this blog

Koodallur Mana: Heritageous mansion

By
K oodallur Mana is in Palakkad district in Kerala. After catching a Guruvayur bus it will lead you to a place named ' Vavannur' . Kudallur Mana is 1km nearby from that area. The name ' Koodal' came from the union of two rivers Bharatpuzha and Thoothapuzha . Koodallur mana exists on the banks of those two rivers. It is the only place where there Saint Pathanjali's dedication exist.  http://anurageros.blogspot.in/2017/10/koodallur-mana-heritageous-mansion.html Mana has experienced over 14 generations. The malayali Namboodiris of the Mana are the clans of Agnihotri . Once sanskrit was the language of litigation in Mana.  The art works found on the front door and roof above the threshold are really surprising. Koodallur Mana is 450years old. Two ponds which have steps are built still exist here. Mana owns 5 wells. There were two storage bin houses and they are broken now. Non namboodiri students where studied by staying there at the bin houses. Serpent ...
Post a Comment
Read more

Safety Operating Procedures required in an LPG plant

By
https://anurageros.blogspot.in/2017/09/safety-operating-procedures-required-in.html STANDARD OPERATING PROCEDURES : LEAK DETECTOR (VL/BL DETECTION) 1.        DRAIN OUT THE WATER FROM THE AIRLINE . BLOW OUT DIRT AND WATER FROM THE FILTER REGULATOR UNIT OF LD-01. CLEAN ALL THE PHOTO DIFFUSIVE SENSORS OF LD-01 2.        RESET LD-01 BY PRESSING THE (.) DOT BUTTON ON THE TOP RIGHT CORNER OF HMI AND WAIT TILL ‘CUC IN PROCESS MODE’ DISPLAYS. PRESS START BUTTON 3.        PUT VL TEST CYLINDER ON THE CONVEYOR. 4.        CHECK WHETHER THE UNIT IS REJECTING IT OR NOT. IF THE CYLINDER IS NOT GETTING REJECTED ADJUST THE SENSITIVITY SO THAT VL CYLINDERS OF LEAKAGE ABOVE 0.5GM/HR ARE REJECTED. 5.        CARRY OUT THE CHECK EVERY TWO HOURS AND RECORD IT. STANDARD OPERATING PROCEDURES : LEAK DETECTOR (O RING LEAK DETECTION) 1. ...
1 comment
Read more

Machining Processes & Machine Tool operations MCQ Mechanical

By
1. The cutting edge of the tool is perpendicular to the direction of tool travel in                                   A. Orthogonal cutting of metals  B. Oblique cutting of metals C. Both a and b D. None of these Ans: Orthogonal cutting of metals 2. The cutting edge of the tool is inclined at an angle less than 90 to the direction of tool travel in A. Orthogonal cutting of metals B. Oblique cutting of metals C. Both a and b D. None of these Ans: Oblique cutting of metals 3. Two components of the cutting forces which are perpendicular acting on the cutting tool in A. Orthogonal cutting of metals B. Oblique cutting of metals C. Both a and b D. None of these Ans: Orthogonal cutting of metals 4. Orthogonal cutting systems are also known as A. One dimesional cutting system B. Two dimensional cutting system C. Three dimensional cutting system D. none of ...
3 comments
Read more