Skip to main content

RRB Examination Previous Question papers and Repeated questions

Railway Recruitment Board has notified for recruitment vacancies available for Assistant Loco Pilot and various Technician posts in different units of Indian Railways. Upto 18000 vacancies available for the post of ALP and 9000 Vacancies for the post of Technicians.


The question paper includes all the relevant questions from Technical and non Technical sections:
Technical section includes :Mechanical,Electrical and Civil & Non Technical includes :Chemistry,Physics,Mathematics and General aptitude along with current affairs and GK.

Mechanical Type questions:


1. The amount of heat required to convert 5gms of ice at -20degree to steam at 100 degree?
   Ans. 3725 calories
2. Bernoullis theorem applicable to?
   Ans. Static fluid pressure


Electrical Type questions:
1. Ampere is used to measure?
  Ans. Current
Civil Type questions:


Chemistry:

1. Which oxide of nitrogen is formed when Ammonium nitrate is heated?
  Ans. N2O
2. The strongest reducing agent among following: Formic acid,Acetic acid,Propionic acid,Chloro acetic acid, Nitric acid
   Ans. Propionic acid
3. Amino acids are produced by the hydrolysis of :
  Ans. Proteins
4. Electrolysis of aqueos solution of sodium succinate gives
   Ans. C2H2

Physics:
1. Energy in sun is produced as a result?
   Ans. Fusion
2. If 3/4th of a radio active element decays in one hour its half life period will be:
   Ans.
3. The colours of thin film result due to ?
   Ans. Interference of light
4. Susceptibility of air medium is
   Ans. Zero
5. Co ordinates of inflection of normal curve is
  Ans. m plus or minus sigma


Mathematics:

GK,General Aptitude&Current affairs:

1. P Gopichand is associated with?
    Ans: Badminton
2. Princess Diana was killed in a car accident in:
   Ans. France
3. Tulsidas became famous during the reign of:
   Ans. Akbar
4. "The sphinx" is located in
   Ans. Egypt
5. The first man to go in to space was?
   Ans. Yuri Gagarin
6. Dr. Christian Barnard performed the first
  Ans. Heart Transplant

Comments

Popular posts from this blog

Koodallur Mana: Heritageous mansion

K oodallur Mana is in Palakkad district in Kerala. After catching a Guruvayur bus it will lead you to a place named ' Vavannur' . Kudallur Mana is 1km nearby from that area. The name ' Koodal' came from the union of two rivers Bharatpuzha and Thoothapuzha . Koodallur mana exists on the banks of those two rivers. It is the only place where there Saint Pathanjali's dedication exist.  http://anurageros.blogspot.in/2017/10/koodallur-mana-heritageous-mansion.html Mana has experienced over 14 generations. The malayali Namboodiris of the Mana are the clans of Agnihotri . Once sanskrit was the language of litigation in Mana.  The art works found on the front door and roof above the threshold are really surprising. Koodallur Mana is 450years old. Two ponds which have steps are built still exist here. Mana owns 5 wells. There were two storage bin houses and they are broken now. Non namboodiri students where studied by staying there at the bin houses. Serpent ...

Safety Operating Procedures required in an LPG plant

https://anurageros.blogspot.in/2017/09/safety-operating-procedures-required-in.html STANDARD OPERATING PROCEDURES : LEAK DETECTOR (VL/BL DETECTION) 1.        DRAIN OUT THE WATER FROM THE AIRLINE . BLOW OUT DIRT AND WATER FROM THE FILTER REGULATOR UNIT OF LD-01. CLEAN ALL THE PHOTO DIFFUSIVE SENSORS OF LD-01 2.        RESET LD-01 BY PRESSING THE (.) DOT BUTTON ON THE TOP RIGHT CORNER OF HMI AND WAIT TILL ‘CUC IN PROCESS MODE’ DISPLAYS. PRESS START BUTTON 3.        PUT VL TEST CYLINDER ON THE CONVEYOR. 4.        CHECK WHETHER THE UNIT IS REJECTING IT OR NOT. IF THE CYLINDER IS NOT GETTING REJECTED ADJUST THE SENSITIVITY SO THAT VL CYLINDERS OF LEAKAGE ABOVE 0.5GM/HR ARE REJECTED. 5.        CARRY OUT THE CHECK EVERY TWO HOURS AND RECORD IT. STANDARD OPERATING PROCEDURES : LEAK DETECTOR (O RING LEAK DETECTION) 1. ...

Machining Processes & Machine Tool operations MCQ Mechanical

1. The cutting edge of the tool is perpendicular to the direction of tool travel in                                   A. Orthogonal cutting of metals  B. Oblique cutting of metals C. Both a and b D. None of these Ans: Orthogonal cutting of metals 2. The cutting edge of the tool is inclined at an angle less than 90 to the direction of tool travel in A. Orthogonal cutting of metals B. Oblique cutting of metals C. Both a and b D. None of these Ans: Oblique cutting of metals 3. Two components of the cutting forces which are perpendicular acting on the cutting tool in A. Orthogonal cutting of metals B. Oblique cutting of metals C. Both a and b D. None of these Ans: Orthogonal cutting of metals 4. Orthogonal cutting systems are also known as A. One dimesional cutting system B. Two dimensional cutting system C. Three dimensional cutting system D. none of ...